This standard is issued under the fixed designation D ; the number 1 This test method is under the jurisdiction of ASTM Committee D on Rubber. ASTM D is an abrasion method used for coated materials and is cited for classification testing by the ANSI standard. ASTM D Abrasion resistance tests are intended to measure the wear resistance properties of a material. This may be correlated to expected end use.
|Published (Last):||1 October 2009|
|PDF File Size:||7.25 Mb|
|ePub File Size:||12.65 Mb|
|Price:||Free* [*Free Regsitration Required]|
MIL-DTLF Military Specification r3389 Plates, Tags, and Bands for Identification of Equipment This specification covers the materials and physical characteristics of plates, tags and bands identification devices used for identification of equipment. This method covers the selection criteria for hand protection systems including chemical permeation, puncture resistance, and abrasion resistance.
Resilient floor coverings – Determination of wear resistance – Part 2: This guide is intended to assist in establishing atm for determining the relative resistance of treated or untreated mortar surfaces.
Some test methods are included, but most sections refer to specific ASTM test methods. Laminate floor coverings – Elements with a surface layer based on amnioplastic thermosetting resins – Specifications, requirements and test methods. Frick-Taber Test This European Standard describes the Frick-Taber method for determining the wear resistance of the wear layer of polyvinyl chloride floor coverings under laboratory conditions.
This explains the s3389 for both residential and contract spaces. This specification covers a rubber-base paint for interior use on concrete floors.
This test method covers the determination of the resistance to abrasion of fabrics coated with rubber or plastics. This Japanese Industrial Standard applies to building materials and parts of building construction and specifies the testing method to evaluate the degree of abrasion of the d389 piece. Thin, Hard, Dense Deposit This specification s3389 the engineering requirements for the deposition of a thin, hard dense chromium coating on surfaces of ferrous and non ferrous alloys and the properties of the coating.
The test method is applicable to floor coverings with smooth surfaces.
Abrasion – Argen Polymer LLC
The purpose of this test is to determine whether the plastic has a certain minimum resistance to abrasion. Basic Format Specifications The entrance surface of the disc should have sufficient scratch resistance, which may be improved by a protective coating. This commercial item description covers catalyzed epoxy system of marking inks for metallic or other non-porous surfaces and printed wiring boards.
Fabric samples are mounted asttm and rubbed in a figure eight like motion using a piece of worsted wool cloth as the abradant. This guide covers the selection and use of test methods for high-performance interior architectural wall coatings HIPAC which differ form more conventional coatings in that they are tougher, more stain-resistance, more abrasion-resistant and, ordinarily, designed to be applied to wall surfaces of steel, masonry, and plaster or gypsum wallboard.
Testing Methods This method specifies the testing methods for determination of abrasion resistance satm rubber, vulcanized or thermoplastic hereafter referred to as “vulcanized rubber”.
This D338 Standard specifies mechanical test methods relating to the safety requirements for all safety glazing materials in a road vehicle, whatever the type of glass or other material of which they are composed. This European Standard describes the Frick-Taber method for determining the wear resistance of the wear layer of polyvinyl chloride floor coverings under laboratory conditions.
In an effort to bring further clarity to the appropriate consideration of double rub numbers, as of April 1,textile companies and furniture manufacturers that use the ACT certification mark for abrasion on their samples will now include the following statement whenever publishing test results in excess ofdouble rubs: To determine the abrasion resistance of chemical atm fabrics and films using a rotary platform double head tester.
This specification establishes the engineering dd3389 for producing a hard anodic coating on aluminum and aluminum alloys and the properties of such coating. BS EN Surfaces for sports areas – Asm of resistance to abrasion of non-filled synthetic turf This document describes a method for the determination of the wear resistance of a non-filled synthetic turf surface using an abrasive wheel under laboratory conditions.
DIN and Taber 5155 Abrasion
This Standard applies to high pressure decorative laminates for use as work and nonwork surfaces of food service equipment on which direct food contact during normal preparation or holding operations is not intended, expected, or reasonable.
This part of ISO specifies a method for determining the resistance to abrasion of a dried film of paint, varnish or related product, using abrasive rubber wheels and abrading by making a rotary movement. The test is used to determine the desired wear characteristics are met. This guide covers and is intended to assist in establishing procedures for conducting wear tests of rigid or flexible materials utilizing the rotary platform abraser.
See tests 12 and Determination asm Properties The test measures the ability of the decorative surface of the sheet under test to resist abrasive wear-through to the sub-layer. Test Method B uses a device that contains a wheel that has been fitted with abrasive paper. Mechanical property of film — Section 9: ISO Paints and Varnishes; Determination of Resistance to Abrasion This part of ISO specifies a method for determining the resistance to abrasion of a dried film of paint, varnish or related product, using abrasive paper attached to wheels and abrading by making a rotary movement ISO Paints and Varnishes; Determination 3d389 Resistance to Abrasion This part of ISO specifies a method for determining the resistance to abrasion of a dried film of paint, varnish or related product, using abrasive rubber wheels and abrading by making a rotary movement ISO Plastics; Determination of Resistance to Wear by Abrasive Wheels This International Standard specifies a general method for asmt the resistance to abrasive wear of plastics under the action of abrasive wheels.
This specification covers three types, four classes, and two forms of laminated or coated cloth. This is an oscillating test. This specification covers adhesive-backed metal foil identification or instruction plates, herein referred to as identification plates, for use as internal and external asttm identification or instruction see 6.
EN Annex E Laminate floor coverings – Elements with a surface layer based on amnioplastic thermosetting resins – Specifications, requirements and test methods This annex specifies the method for measuring abrasion resistance and consequently determining the abrasion class of laminate floor covering elements. Toggle navigation Top Links.
This Standard is one of a series of standards dealing with the sampling and testing of paints, varnishes and related products.
It shall be used when specified on the Engineering drawing. ASTM D Standard Guide for Testing Industrial Water-Reducible Coatings This guide covers the selection and use of procedures for testing water-reducible coatings, both pigmented and clear, utilizing synthetic lattices, synthetic resin emulsions, or water-reducible alkyds.
Martindale Test Video —. This European standard specifies the characteristics of agglomerated cork with a wear layer based upon polyvinyl chloride and modification thereof. The specification applies only to a membrane system that has an integral wearing surface. This Japanese Industrial Standard specifies the testing method for laminated thermosetting decorative sheets.
This test method covers the establishment of an abrasive wear index by determination of the loss of weight resulting from abrasion of unglazed ceramic tile. EN Wood flooring – Test methods to determine elasticity and resistance to wear and impact resistance This document specifies two alternative test methods to determine the resistance to wear of lacquered wood floorings and one method to test the elasticity of the lacquer. Wyzenbeek results abovedouble rubs have not been shown to be an indicator of increased lifespan.
Wyzenbeek — New Test Video. This Japanese Industrial Standard specifies the testing method for the abrasion resistance of plastics by abrading the test piece, particularly in, with an abrasive wheel. This specification covers the materials and physical characteristics of plates, tags and bands identification devices used for identification of equipment.
This may be correlated to expected end use performance.
This specification covers prefaced concrete masonry units with the exposed-to-view-in-place surfaces covered at the point of manufacture with resin, resin and astn filler, or cement and inert filler to produce a smooth resinous tile facing.