AHM E8/E8M – 13a. G–Gauge length. Dimensions, mm [in.] For Test Specimens with Gauge Length Four times the Diameter (E8]. Standard. Small-Size. Buy ASTM E 8/E8M: A TEST METHODS FOR TENSION TESTING OF METALLIC MATERIALS from SAI Global. Originally contact ASTM Customer Service at [email protected] For Annual Book of ASTM approved in Last previous edition approved as E8/ E8M.
|Published (Last):||22 July 2010|
|PDF File Size:||11.43 Mb|
|ePub File Size:||11.37 Mb|
|Price:||Free* [*Free Regsitration Required]|
It is important, therefore, that care be exercised in the preparation of specimens, particularly in the machining, to maximize precision and minimize bias in test results. Astm c astm normas fibra de vidrio.
Originally approved in Extensometers shall be used and verified to include the strains corresponding aatm the yield strength and elongation at fracture if determined.
Proper alignment of wedge grips and liners is illustrated in Fig. Adtm wedge grips generally furnish a satisfactory means of gripping long specimens of ductile metal.
ASTM E8.E8M Tensiont testing of metallic materials –
Such interpretation is usually applicable to values for reduction of area reported in the literature when no further qualification is given. Both of these gripping devices should be attached to the heads of the testing machine through properly lubricated sphericalseated bearings.
If, however, for any reason, one grip of a pair advances farther than the other as the grips tighten, an undesirable bending stress may be introduced. NOTE 1—The effect asym this eccentric force application may be illustrated by calculating the bending moment and stress thus added. This requires that liners of several thicknesses be available to cover the range of specimen thickness.
No further reproductions authorized. Combining values from the two systems may result in non-conformance with the standard.
The values stated in each system are not exact equivalents; therefore each system must be axtm independently of the other. The test methods have been used extensively in the trade for this purpose. Parte 1 de 8 Designation: It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
For short specimens and awtm specimens of many materials it is generally necessary to use machined test specimens and to use a special means of gripping to ensure that the specimens, when e8mm load, shall be asttm nearly as possible in uniformly distributed pure axial tension see 5. A number in parentheses indicates the year of last reapproval.
Brittle Materials—A schematic diagram of a gripping device for threaded-end specimens is shown in Fig. For a standard Astm a Astm a NOTE 3—Punching or blanking of the reduced section may produce significant cold work or shear burrs, or both, along the edges which should be removed by machining. The distance between spherical bearings should be as great as feasible. C39M – 16 – Compressive Strength of Cylindrical For best results, the wedges should be supported over their entire lengths by the heads of aetm testing machine.
For measuring elongation at fracture with an appropriate extensometer, the gauge length of the extensometer shall be equal to the nominal gauge length required for the specimen being tested.
ASTM E8.E8M -15-Tensiont testing of metallic materials
This error increases to 2. The gauge length is the most significant difference between E8 and E8M test specimens. Current edition approved May 1, The forces used in determining tensile strength and yield strength shall be within the verified force application range of the testing machine as defined in Practices E4.
For proper gripping, it is desirable that the entire length of the serrated face of each wedge be in contact with the specimen. Any departure from this requirement may introduce bending stresses that are not included in the usual em8 computation force divided by cross-sectional area. E8M Tensiont testing of metallic materials Juliano row Enviado por: A superscript epsilon indicates an editorial w8 since the last revision or reapproval.
This information may be useful in comparisons of materials, alloy development, quality control, and design under certain circumstances. For this reason, a e88 taper is permitted in the reduced section of each of the specimens described in the following sections. To ensure axial tensile stress within the gauge length, the axis of the test specimen should coincide with the center line of the heads of the testing machine.
When liners are used behind the wedges, they must be of the same thickness and their faces f8 be flat and parallel.