CCNA 3 Final Exam Answers version v – % Full, CCNA v5. v The new switch has a VTP revision number of 4. CCNA v Routing and Switching Exam Answers , Free CCNA Study Guide, Tutorials, Labs, Practice Exams. CCNA Security, , v CCNA 2 v Capitulo 4 Examen Online en Español Cisco CCNA 1 Capitulo 4 Examen Pregunta 13 Cisco CCNA2 v Capítulo 3 Examen Pregunta

Author: Kazizshura Yozshuzuru
Country: Russian Federation
Language: English (Spanish)
Genre: Video
Published (Last): 28 February 2014
Pages: 324
PDF File Size: 18.4 Mb
ePub File Size: 17.76 Mb
ISBN: 349-4-85726-234-4
Downloads: 38162
Price: Free* [*Free Regsitration Required]
Uploader: Grok

This page is maintained by: SW1 drops the traffic because it is untagged.

How does SW1 manage traffic coming from Host A? What is the purpose of the Spanning Tree algorithm? The OFDM modulation technique results in a slower data rate.

Examenes Cisco CCNA v en Español

What two methods can be used to remove MAC address table entries from a cnca It is configured in VTP server mode. Downloading to the startup-config requires the switch to be reloaded in order for the configuration to take effect.

Users complain that they do not have vcna to the web server that is connected to SW1. Which STP port type can only appear once on a segment, and must be present in order for traffic to flow on that segment? Power cycle the switch to clear all dynamically learned addresses.


CCNA 3 Final Exam V4.0 Answers

The switch port is able to trunk if the remote switch port is set to desirable. The port will transition into blocking state and then immediately into forwarding state. October 17, at 3: The PC is set to full duplex.

November 30, at 8: What is one disadvantage that April 9, at 2: October 18, at 3: Associate with the access point and then open a HyperTerminal session with the access dezcargar.

Configure the switch with the same VTP domain name as other switches in the network. The ip domain-name command must also be entered in line configuration mode for the vty lines. The use of higher frequencies means that signals cvna more likely to be obstructed. Which method establishes an administrative connection for configuring the Linksys WRTN wireless access point?

Which three statements are correct concerning the default configuration of a new switch? July 4, at 5: Which two steps should the administrator perform to achieve this? Which three options correctly identify information that could be associated with this output? Student Lab Manual 5.

Download The Cisco Report Today! Data traffic passes untagged through the phone to the switch. It is sending and receiving data frames. Reply Marcelo Soares says: The CCNP curriculum examines complex networking concepts, such as troubleshooting tools and more sophisticated configurations. Freeware for Solaris Unix sunfreeware.


With a CCNP, a network professional can install, f4.0, and operate LAN, WAN, and dial access services for organizations with networks from to more than nodes, including but not limited to these protocols: July 13, at 2: When the auto-MDIX feature is enabled, the switch detects the required cable type for copper Ethernet connections and configures the interfaces accordingly. October 12, at 6: No routing protocol is configured on Router1. Switches S2 and S3 are properly connected using an ethernet cable.

March 8, at 1: Which IP address should be assigned to this new host? The configuration steps that are listed in the exhibit have been entered in switch S1 via the console.

CCNA 3 Final Exam V Answers

deecargar The VTP configuration revision is different on both switches. In a three-layer hierarchical network design, which distribution layer function delineates broadcast domains?

VTP v2 is disabled.

Both the teacher and student will be able to receive data but only the teacher will be able to send. September 26, at 6: