E/ECE/ Rev.1/Add/Rev.2 E/ECE/TRANS/ Regulation No. 43 page 4 CONTENTS (continued) Annex 3 Annex 4 Annex 5 Annex 6 Annex 7 Annex 8. Mr. Masaru Morikawa, General Safety Subcommittee, JASIC. – Safety Glass Testing according to ECE R Mr. Pham Minh Thanh. E/ECE/TRANS/) November 2, STATUS OF UNITED NATIONS REGULATION ECE UNIFORM PROVISIONS CONCERNING THE APPROVAL.

Author: Groshura Zulumuro
Country: Nicaragua
Language: English (Spanish)
Genre: Marketing
Published (Last): 21 June 2006
Pages: 40
PDF File Size: 12.98 Mb
ePub File Size: 10.19 Mb
ISBN: 271-8-96544-867-4
Downloads: 40583
Price: Free* [*Free Regsitration Required]
Uploader: Vorn

The materials used, 3.

Alternatively a curved pane may be tested. In the case of a windscreen: Interpretation of Results 6. The presence or absence of conductors or heating elements. The impact surface of the felt cover shall be replaced after 12 tests. Flat and curved glass panes. Number of Test Pieces 4. In the case of split windscreens, no measurements shall be made in a strip 35mm from the edge of the windscreen, which is adjacent to the dividing, pillar. For the type of lamp specified in Paragraph 6. The distance between the internal faces of the wheels shall be The projection axis in the horizontal plane shall be maintained approximately normal to the trace of the windscreen in that plane.

Consider that the modifications e43 are unlikely to have an appreciable adverse effect fce, in the case of windscreens, that the new type comes within the approved group of windscreens, and that in any case the safety glazing material still complies with the requirements; or 9.

After exposure, measure the regular light transmittance again in the exposed area of each test piece. For each point of impact the fragmentation test shall be considered to have given a satisfactory result if the total surface area of fragments having a surface area of more than 2cm comprised in a rectangle as defined in Annex 4, Paragraph 2. This free end shall be supported horizontally by an appropriate device until the test begins.

Test of Resistance to Abrasion 5. The approval granted in respect of a type of safety glazing material pursuant to this Regulation may r4 withdrawn if the requirement laid down in Paragraph In the case of windscreens, to check residual visibility after shattering.


Automotive Glass Testing in Compliance with ECE R43 | WO | TÜV Rheinland

The provisions of this Annex shall be considered to be met if the glazing submitted for approval is of the same composition as a windscreen already approved under the provisions of Annex 6 or Annex 8 or Annex 9. There is a neck-shaped intermediate piece between the spherical part and the cross-beam and a mounting rod on the other side of the cross-beam. A test shall be deemed to have given a satisfactory result if fragmentation satisfies the following conditions: Tell me more Already a subscriber.

No bubbles or other visible decompositions, discolourations, milkiness or crazing shall occur d43 weathering. A wiper carriage assembly see 1 in Figures 11 and 12 having a beam which spans across the width of the base apparatus and can be mounted at its ends to the pillars, furthermore this carriage assembly has two self-supporting arms see 2 in Figures 11 and 12 where a wiper holder can be attached the distance between the sample surface and bearing of self-supporting arm at the carriage assembly is to mm4.

The drop heights measured from ecw lowest point of the phantom head to the surface of the impact plate are 50,and mm. All results shall be recorded. Nature and type of plastics coating s: These conditions shall be maintained throughout the tests. Test of resistance to high temperature in accordance dce the requirements of Annex 18, Paragraph 6.

VW T25 Opening Quarter Light Glass LHS Ece-r43 E37 C9065

Nominal thickness of plastics coating s: Power-supply transformer and capacitor capable of supplying to the lamp Paragraph 6. Three flat square test pieces of mm for each type of surface shall be subjected to testing.

Water spray will be directed d43 against the test specimen surface facing the light source.

Benefits at a Glance. The method used shall be that described in Annex 3, Paragraph 3. This beam shall not be vignette at either port of the sphere. Manufacturer’s name and address NET Our online subscription service, offering immediate access to our extensive library of global vehicle regulations, standards and legislation. A set of test pieces or samples submitted for approval shall be considered satisfactory from the point of view of the resistance to simulated weathering if all test pieces have given a satisfactory result.


In case the specific device has a significantly different cross profile it might be necessary to adapt the wiper blade holder respectively. Number of Test Pieces Four test pieces from the smallest-developed-area series and four samples from the largest-developed-area series selected in accordance with the provisions of Annex 13, shall be tested.

The ball shall strike that face of the test piece which represents the inward face of the safety-glass pane when the latter is mounted on the vehicle. The composition of the multiple-glazed unit symmetrical, asymmetrical1. Any opaque obscuration bounded downwards by Plane 1 and laterally by Plane 4 and its symmetrical in relation to the longitudinal median plane of the vehicle Plane 4′ ; But taking into account the fact that the datum points as defined under Paragraph 2. Impact head form Impact of stones Optical distortion Light transmittance.

Colouring of the plastic product: Measure, according to Paragraph 9. Annex 2A to this Regulation gives examples of arrangements of approval marks. The sample box shall be placed into the stainless steel tray and fixed using adhesive tape on the two short sides of the box according to Figure B. Interpretation of Results 7. The HIC value is also to be measured. The sample is not penetrated nor shall it break into fully separate large pieces.