SKU, Model, PWM Outputs, Ports, 2 Ports, FASST, Telemetry, S- FHSS, High Speed, High Voltage, Connectors, Range. FUTL, RGF, 4, 0, 0. Updating instructions and software manual are included in the zipped files. Please unzip 12FG Model Recovery Application ( KB) – updated July 23, Futaba 12FG – GHz FASST (T12FGA) with GHz TM Module Accessories included: Instruction Manual – Futaba SD Card – 12 V AC.

Author: Maum Akinohn
Country: Dominican Republic
Language: English (Spanish)
Genre: Video
Published (Last): 10 August 2014
Pages: 464
PDF File Size: 10.7 Mb
ePub File Size: 8.15 Mb
ISBN: 184-4-44980-357-7
Downloads: 95137
Price: Free* [*Free Regsitration Required]
Uploader: Vujas

I love throttle cut as an option. I guess this is what endears me to the 12FG. It comes with a 72Mhz Module. Selecting which model you’ll be flying only 12fgn a few simple steps. The 12FG gives a nice graphical display with an actual number as a point of reference.


It is effective in 3D aerobatics which use a large travel. Switch selection method Futabs various functions used in the T12FG can be selected by switch.

I did have one or two reservations though. The fuatba is not functional at high throttle to avoid accidental dead sticks. The sub-trim menu allows you to fine tune the neutral position so your control surfaces are precisely where they need to be for flight. SWASH MIX The swash mix function is used 12fgj correct the Example of use swash plate in the aileron roll direction and elevator cyclic pitch corresponding to each operation of each condition.

A warning beep is emitted if you try to power up with a non-default flight condition — this could save a few undercarriages being retracted on the ground. The 12FG fits comfortably in my hands. Thanks to the use of plug-in RF modules, the Futaba 12FG offers a genuine all-in-one solution for those with 35 MHz gear who may wish migrate to 2. Nevertheless, retrimming was accomplished with great ease and soon the Sting was having a ball. If you have any difficulties while using your system, please consult the manual, our online Frequently Asked Questions on the web pages referenced belowyour hobby deal- er, or the Futaba Service Center.


When the EDIT button is pushed for 1 second, the delay time is reset to the initial value.

Futaba R6303SB S.Bus High-Speed Micro 3-18Ch Receiver

Aircraft, Glider, Heli Current drain: All in all, the user interface is consistent and reasonably quick, though the consistency breaks slightly when it comes to fuutaba individual manusl screens. When the aileron stick is manipulated, the aileron and brake flaps perform the aileron operation simultaneously and the operation characteristic of the roll axis is improved. This lowers the idle speed of the engine.

Receiver nomenclature Before using the receiver, be sure to read the precautions listed in the following pages. The remaining controls comprise a pair of rotary knobs and eight switches. The setting screen appears.

Futaba 12FG Review

Think how many times this one feature alone would have saved our models. BUTTERFLY This function allows powerful brake operation by simultaneously raising the left and right ailerons and lowering the flaps camber flap, This setting manjal allow the ailerons to be raised while the flaps are simultaneously lowered.

Discussions on this Product Show user ratings Check for Retailers. Funky Cub cc ARF. A typical futabw screen is shown selection, frequency setting, end point setting, and below.

Let’s see if it lives up to expectations. The 14 channel RDPS features a wireless frequency setting allowing changes in frequency to be manhal from the transmitter.

Switch selection screen example Switch selection When stick, trim lever, or knob selected Page 38 Helicopter basic setting procedure This section outlines examples of use of the helicopter functions of the T12FG. For each flying surface, the servo’s can be adjusted to a pre-determined spot. I found it’s a very simple process when you know how your 12fh was built and is setup.


Tail configuration options include V-tail and ‘ailevator’ tailerons.

Up to 8 conditions can be commands that apply to helicopters only. In fact, I’m hard pressed to think of a better way it could be done. Perform this setting with the Idle Down function of the Linkage Menu.

Box Champaign, IL Website: This may be a little borderline for some applications, and no doubt some users will wish to replace the pack with higher capacity cells. And just like the 14MZ it offers a viable route into 2. It’s much easier to read and navigate than my 8UAP.

Futaba® Software Downloads/Updates

It also means you can use the 12FG for old and new models alike. The transmitter feels a little too ‘busy’, and I’d have liked unused switches to be removable as on the 12Z and 14MZ. Curve setting examples to 5. When mounting the receiver and servos to the fuselage, connect the necessary points in accordance with the kit instruction manual.

To have this here seems redundant as it’s in the Linkage menu as well. Page Operations related to servo speed Servo speed setting The servo speed at each function operation including flight condition switching can be adjusted. POWER ON The first step after turning on the transmitter is verifying whether you want to transmit a signal, and is the first screen you see. The operation speed can be set in 2 ranges of slow speed flight and high speed operated as a safety function by setting 2 switches.

Note that it is not possible to alter the stick mode after purchase, so make sure you specify the mode before ordering.