HORMANN UAP1 PDF

Find great deals for Hörmann Universaladapterplatine UAP 1. Shop with confidence on eBay!. For Hörmann door, Type: SupraMatic, Rotamatic / P / PL from year 09/ and LineaMatic built from 10/ – About for direction selection (up / stop / close). For inputs to Hormann: does it mean that I have to run 6 wires for this section from Loxone to Hormann? Or is it possible to reuse the wire for

Author: Grojora Gagore
Country: Mali
Language: English (Spanish)
Genre: Spiritual
Published (Last): 11 August 2004
Pages: 224
PDF File Size: 15.14 Mb
ePub File Size: 13.39 Mb
ISBN: 321-4-30944-576-7
Downloads: 15121
Price: Free* [*Free Regsitration Required]
Uploader: JoJolkree

That way I’m able to trace the bus in realtime without the need hormsnn leave the house It’s pretty cold outside at this time uormann the year. Hi Ken, as you say in the beginning of the reply the UAP enables me to “open the garage door” and “close the garage door” which is what I want to achieve same as what the person who wrote the guide I linked to achievedsorry if I didn’t explain properly.

In my case it starts at address 0x8D which is in decimal.

When the board is powered while the logic analyzer is collecting data, we see these bytes comming in:. Drives at least the three relais, maybe more.

Ken 4, 1 4 To control the door via a home automation system you have several options:. That tells me that it appears uxp1 UAP will not allow for the individual movements that you are looking to achieve.

Hörmann Universaladapterplatine UAP 1

Sign up using Email and Password. Exactly what I want to have: Unfortunately the patent doesn’t say anything about the device codes. Whith that one I can tell when the UAP1 is sending and when it is receiving! RX When the board is powered while the logic analyzer is collecting data, we see these bytes comming in: The only things I get from what is stated is that if you press to open – you press the uzp1 again to stop it not hor,ann true move up move down motion.

  HANS IBELINGS PDF

Reverse engeneering the Hörmann UAP1 protocoll

Press the PRG button until the decimal point next to the menu number is illuminated. The remotes require a 2 second press to avoid accidental presses, have you tried making your pulse longer? I see one for your supramatic seems a bit over complicated for a Garage Door – however reading the instructions for the ventilation position You might find what you need here.

Quiescent hormmann circuit open Bit 4: Move the door into the desired position with the buttons andvia the taught-in radio code impulse or an external control element with impulse function.

Pedestrian door Bit 6: Intelligent contol panels Thanks for looking into this! Sign up or log in Sign up using Google.

I might misinterprete some of them at this point: That being said you might be able to program a button to activate open when pressed and to also activate the same function on release. Fortunately the page gives you a nice lookup table for the CRC values which I then used in my Python program to verify all the messages I’ve recorded so far.

Bus scan At startup the Master scans the bus for devices. I am an electronics amateur and can’t figure out based on the schematic below if that is correct?

Hörmann Universaladapterplatine UAP 1 | eBay

I’ll try to extend this artcle or write a followup in the future. No common CRC8 generator gave me the same result as the messages have. Therefore I plan to hook up the bus to a network outlet I have in my garage that leads hormmann the normann down into my basement where my network rack sits.

  LIVRO REVOLUCIONANDO O APRENDIZADO PDF

To supply the board with 24VDC, which normally comes in via the RJ12 connector, I simply used the terminals taht normally connect the switches.

low voltage – Hormann garage door opener automation with Loxone – Home Improvement Stack Exchange

Then I encountered another problem I didn’t think about in the first place. The message can be between 1 and 3 bytes long and the patent states that it can be expanded. I hoped to find the signals there as well but it turned out that is not the case. Later I captured traces using my logic analyzer for each possible command, these are: To change the partial opening position: Post as a guest Name. So I decided to reverse engeneer and document the bus! Sign up using Facebook.

hormxnn Here’s what I got using the USB converter with the door closed idling:. So I basically want a remotely controlled button the app where I click open and it will start moving up until the end position, which should be possible, and it sometimes does move or open, but something must be off with the connection, impulse duration or voltage as it does not work consistently: That occured at baud 8N1 so I think that must be the correct baudrate.

Here’s what I got using the USB converter with the door closed idling: I decided to look at the boards communications without the motor connected. Not referenced Bit 5: